[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
problemi installing fglrx on toshiba m60
- From: "Roberto Antoniazzi" <roberto dot antoniazzi at opencontent dot it>
- Date: Thu, 28 Jul 2005 15:25:38 +0200
Hi all,
I'm trying to install the right video drivers. I followed the instructions
in the site to install the right driver for my laptop's graphic card: ati
radeon x600 se, compiled a new kernel (kubuntu with kernel 2.6.10) with the
right options, built the flgx deb modules and tried succesfully
modprobe fglrx
I then tried
/etc/init.d/kdm restart
but the server does not start.
Here the result of my lsmod and dmesg messages:
lspci:
Module Size Used by
fglrx 230524 0
speedstep_centrino 7892 1
proc_intf 4100 0
freq_table 4100 1 speedstep_centrino
cpufreq_userspace 4572 1
cpufreq_ondemand 6172 0
cpufreq_powersave 1920 0
video 16260 0
sony_acpi 6280 0
pcc_acpi 11264 0
button 6800 0
battery 10244 0
container 4608 0
ac 4996 0
ipv6 229504 9
af_packet 20744 2
yenta_socket 19584 0
pcmcia_core 53568 1 yenta_socket
ipw2200 66156 0
firmware_class 9728 1 ipw2200
ieee80211 21252 1 ipw2200
ieee80211_crypt 5832 1 ieee80211
8139cp 19200 0
8139too 24320 0
mii 4736 2 8139cp,8139too
ohci1394 31876 0
i2c_i801 8076 0
i2c_core 21264 1 i2c_i801
ahci 10500 0
snd_intel8x0 29984 2
snd_ac97_codec 64608 1 snd_intel8x0
snd_pcm_oss 47652 0
snd_mixer_oss 16768 1 snd_pcm_oss
snd_pcm 84872 4 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 23300 1 snd_pcm
snd 50276 9
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 9824 1 snd
snd_page_alloc 9604 2 snd_intel8x0,snd_pcm
usbhid 29376 0
ehci_hcd 29444 0
uhci_hcd 30224 0
usbcore 107384 4 usbhid,ehci_hcd,uhci_hcd
shpchp 86116 0
pci_hotplug 30512 1 shpchp
intel_agp 20636 1
agpgart 31784 1 intel_agp
rtc 12216 0
nls_iso8859_1 4224 1
nls_cp437 5888 1
vfat 12928 1
fat 37792 1 vfat
md 43856 0
dm_mod 53116 1
evdev 9088 0
capability 5000 0
tsdev 7488 0
commoncap 7808 1 capability
sbp2 22408 0
ieee1394 100408 2 ohci1394,sbp2
psmouse 19336 0
mousedev 11160 1
parport_pc 34372 0
lp 10792 0
parport 33480 2 parport_pc,lp
ext3 120968 1
jbd 54168 1 ext3
sr_mod 16036 0
cdrom 36508 1 sr_mod
sd_mod 16784 4
sg 35360 0
ata_piix 8836 9
libata 44548 2 ahci,ata_piix
scsi_mod 119936 6 ahci,sbp2,sr_mod,sd_mod,sg,libata
unix 26164 423
thermal 13576 0
processor 22708 2 speedstep_centrino,thermal
fan 4612 0
fbcon 34048 0
font 8448 1 fbcon
bitblit 5120 1 fbcon
vesafb 6948 0
cfbcopyarea 3968 1 vesafb
cfbimgblt 3072 1 vesafb
cfbfillrect 3584 1 vesafb
dmesg:
LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda6 ro quiet splash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1995.567 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 902044k/917504k available (1436k kernel code, 14948k reserved, 754k
data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3940.35 BogoMIPS (lpj=1970176)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000
00000180 00000000
CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000
00000180 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040 00000180
00000000
CPU: Intel(R) Pentium(R) M processor 2.00GHz stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (bad gzip magic numbers); looks
like an initrd
Freeing initrd memory: 4268k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd904, last bus=7
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: Embedded Controller [EC0] (gpe 29)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn dot helgaas at hp dot com
** so I can fix the driver.
pnp: 00:00: ioport range 0xfe00-0xfe7f has been reserved
pnp: 00:00: ioport range 0xfe80-0xfeff has been reserved
pnp: 00:00: ioport range 0xff00-0xff7f has been reserved
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1122559144.164:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf dot csiro dot au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 388 $ 54 ports, IRQ sharing enabled
ACPI: PCI interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 20
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 3
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
RP01 RP02 USB1 USB2 USB3 USB4 USB7 ELAN MODM BT
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4268KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.10 loaded.
ata_piix version 1.03
ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x18F0 irq 14
ata1: dev 0 cfg 49:2f00 82:746b 83:7d09 84:6023 85:7469 86:3d09 87:6023
88:203f
ata1: dev 0 ATA, max UDMA/100, 194980905 sectors: lba48
ata1(0): applying bridge limits
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
elevator: using anticipatory as default io scheduler
Vendor: ATA Model: TOSHIBA MK1032GA Rev: AB21
Type: Direct-Access ANSI SCSI revision: 05
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x18F8 irq 15
ata2: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
88:0407
ata2: dev 0 ATAPI, max UDMA/33
ata2(0): applying bridge limits
ata2: dev 0 configured for UDMA/33
scsi1 : ata_piix
Vendor: MATSHITA Model: DVD-RAM UJ-840S Rev: 1.52
Type: CD-ROM ANSI SCSI revision: 05
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
SCSI device sda: 194980905 512-byte hdwr sectors (99830 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 194980905 512-byte hdwr sectors (99830 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
Stopping tasks: ==|
Freeing memory... done (415 pages freed)
Restarting tasks... done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 1951856k swap on /dev/sda7. Priority:-1 extents:1
EXT3 FS on sda6, internal journal
lp: driver loaded but no devices found
mice: PS/2 mouse device common for all mice
input: PS/2 Generic Mouse on isa0060/serio4
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 388 $ Ben Collins <bcollins at debian dot org>
ts: Compaq touchscreen protocol output
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel at redhat dot com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 256M @ 0x0
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB
UHCI #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 23, io base 0x1800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB
UHCI #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 19, io base 0x1820
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB
UHCI #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 18, io base 0x1840
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB
UHCI #4
usb 1-1: new low speed USB device using uhci_hcd and address 2
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 16, io base 0x1860
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2
EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem 0xb8000000
usbcore: registered new driver hiddev
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
usb 1-1: string descriptor 0 read error: -71
usb 1-1: string descriptor 0 read error: -71
drivers/usb/input/hid-core.c: ctrl urb status -71 received
input: USB HID v1.00 Mouse [0425:f102] on usb-0000:00:1d.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usb 1-1: USB disconnect, address 2
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hw_random: RNG not detected
usb 1-1: new low speed USB device using uhci_hcd and address 3
input: USB HID v1.00 Mouse [G-Tech CHINA U+P Wireless Mouse ] on
usb-0000:00:1d.0-1
ACPI: PCI interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1e.2 to 64
intel8x0_measure_ac97_clock: measured 49515 usecs
intel8x0: clocking to 48000
ohci1394: $Rev: 388 $ Ben Collins <bcollins at debian dot org>
ACPI: PCI interrupt 0000:06:00.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[c4004000-c40047ff]
Max Packet=[2048]
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 21
eth0: RealTek RTL8139 at 0x6000, 00:0f:b0:83:58:16, IRQ 21
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
ieee80211_crypt: registered algorithm 'NULL'
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 0.19
ipw2200: Copyright(c) 2003-2004 Intel Corporation
ACPI: PCI interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 22
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
ACPI: PCI interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:06:04.0 [1179:ff01]
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000006
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f5576400a8b]
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f0500(lo)
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ibm_acpi: ec object not found
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
eth0: no IPv6 routers present
fglrx: no version for "struct_module" found: kernel tainted.
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg,
GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 805 MBytes.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[fglrx] module loaded - fglrx 8.14.13 [Jun 8 2005] on minor 0
Access to /proc/cpufreq is deprecated and will be removed from (new) 2.6.
kernels soon after 2005-01-01
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
hub 1-0:1.0: port 1 disabled by hub (EMI?), re-enabling...
usb 1-1: USB disconnect, address 3
usb 1-1: new low speed USB device using uhci_hcd and address 4
input: USB HID v1.00 Mouse [G-Tech CHINA U+P Wireless Mouse ] on
usb-0000:00:1d.0-1
thank you in advance
roberto